Blogjet751

Wake on Lan is a hardware / software solution that allows a computer to be remotely woken. A computer that has a network connection and is ACPI (Advanced Configuration Power Interface) compatible can be remotely enabled.

1. Teamviewer Wake Up On Lan
2. Teamviewer Wake Up On Lan Macbook
3. Teamviewer Manual Wake On Lan

As a reminder, the Wake On LAN function enables remote stations to be woken up by sending a 'Magic' packet over the network. For this packet to be correctly formed, you need to indicate the MAC address of the network card on the remote computer, along with its broadcast address.

In a first, Wake on Lan must be enabled in the BIOS of the computer, and then configured in the operating system.
To enable Wake on Lan in the BIOS (below for Intel motherboards):

Yes, you can wake up a computer/laptop via Wake-on-LAN using your tablet or smartphone. To do so, you must configure TeamViewer Wake-on-LAN via your router (DynDNS) or TeamViewer IDs as described above. This allows you to wake up your laptop, computer, workstation, or other devices that are running Windows or Mac OS X.

1. To enable Wake-on-LAN, open System Preferences → Energy Saver and check ‘Wake for Wi-Fi network access’. Mac uses the standard WoL port 9.
2. Download Magic Packet - Wake On LAN and enjoy it on your iPhone, iPad, and iPod touch. ‎USE CASES: - Wake up the computer for connecting over TeamViewer/VNC/RDP - Turning on/off computers for.
3. Yes, you can wake up a computer/laptop via Wake-on-LAN using your tablet or smartphone. To do so, you must configure TeamViewer Wake-on-LAN via your router (DynDNS) or TeamViewer IDs as described above. This allows you to wake up your laptop, computer, workstation, or other devices that are running Windows or Mac.

1. Press F2 during boot to enter the BIOS setup.
2. Access the power menu.
3. Set Wake-on-LAN to turn on the power.
4. Press F10 to save and exit the BIOS setup.

To configure Wake On Lan in Windows 8, Windows 7, Windows 10:

Press Windows key + X to bring up the hidden quick access menu:

1. Select Device Manager.
2. Expand the Network Adapters section.
3. Right-click the adapter that you are currently using, and then click Properties.
4. Click on the advanced tab.
5. Select Wake on Magic package from the list of properties.
6. Expand the value section and select enabled.
7. Click Power Management tab.
8. Select the Allow this device to wake the computer check box.
9. Click OK.

To configure Wake On Lan in Windows XP:

1. Click Start> Settings> Control Panel.
2. Double-click system.
3. Click the Hardware tab, and then click Device Manager.
4. Expand the Network Adapters section.
5. Right-click your adapter and select Properties.
6. Click on the Advanced tab.
7. Select Wake-on-LAN Options and click Properties. Define the following elements:
   1. Enable PME: set to enabled
   2. Wake on Settings: Set to wake up on Magic Packet

IMPORTANT: The computer must be in either Sleep or Hibernation mode for this to work.

Once these prerequisites have been verified, we can use the Wake On Lan function from our software.

First, download the free 30 day version of our software if you have not installed it yet: Download IDEAL Administration.

Once installed, just execute it under a domain admin account.

• 'Wake On LAN' function via the graphic interface

Select Computers menu and Wake (Wake On Lan)

IDEAL Administration & IDEAL Remote provide simple management of Wake On LAN.
You can retrieve automatically all MAC and broadcast addresses for a group of computers or a range of IP addresses (Action menu then Automatic addition).
Or manually add a Wake on LAN configuration (Action menu, then Manual addition).
You can also configure the port to use for sending the packet (default port is 9).
To send the wake-up packet to one or more computers on your network, check them from the list, then click the Action button then Wake up.
You can also schedule and automate the use of Wake On LAN: check the target computers from the list , then click the Action button then Schedule.
You will then be prompted to create a scheduled task.
You can save or open a selection of computers from buttons provided for this purpose.

• 'Wake On LAN' function via Command line

IDEAL Administration & IDEAL Remote let you run the Wake On LAN function from the command line.
Command format:
IA.exe WOL /mac:00-11-22-33-44-55 /ip:ip_address/port:port_number (default port is 9) /file:'file.wol'
/mac: MAC address (required)
/ip: broadcast address (optional; if omitted, the default broadcast address is used)
/port: port used for sending the packet (optional; if omitted, default port 9 is used)
/file: file .wol containing the list of computers to wake. The wake-up packet is sent to all the computers listed in the file. Optional feature.

From DD-WRT Wiki

[edit]Introduction

Wake-On-LAN (WOL) provides the ability to wake a slept/suspended, hibernating, or shut down computer, but the support for this (especially the latter) is dependent upon the hardware and BIOS/UEFI settings. Most modern computers have the WOL feature - it might be listed under PME (Power Management Events).

Reasons to use WOL with DD-WRT:

• You do not want a computer on all the time, yet you want to use it from outside your home or office, and there is a DD-WRT-enabled device as the Internet gateway for that computer, powered on all the time.
• The computer is a media server that auto-sleeps, but you want it to wake automatically for file access.

[edit]Preparation

You will need:

1. A PC which supports WOL. Most modern PC's can be set-up this way.
2. Administrative access to the computer you want to sleep/wake-up.
3. The WOL computer should have a static IP address, one manually assigned or through static DHCP. In the example below, we assume your router LAN is 192.168.1.x (the default) and the static IP WOL computer is 192.168.1.254.
4. Ideally, a second PC to test the WOL abilities of the first one. You can also use the DD-WRT device's Web Interface to send test packets, in place of a second PC.

[edit]Enable WOL on the Computer

1. On the LAN adapter of the computer (physical ethernet adapter and/or wireless, given BIOS support), choose Properties/Configure.
2. Power Management tab (far right). Check the second and third boxes to enable WOL. Press OK until you are back at Network Connections. Now the computer can normally be started from Hibernate, Standby, or PowerOff modes via a special management packet.
3. Get ready to test your set-up by using a utility like WOL Magic Packet Sender http://magicpacket.free.fr/ (free). Install it on both the computer you are using and a second PC on the same physical LAN.
4. On the WOL computer, open WOL Magic Packet and on the Receive tab, click the green Start button.
5. On the second computer, open WOL Magic Packet and on the Send tab, put in:
   1. IP Address of WOL computer for Host Name
   2. 0.0.0.0 for Subnet Mask (select from drop-down)
   3. MAC address of LAN adapter on WOL computer. Use the command 'ipconfig /all' if you don't know what this is.
6. Click the green Send button. The WOL computer should respond with a pop-up box showing a packet was received.

Repeat the previous steps and go over the trouble-shooting tips until they work before proceeding.

[edit]Test that WOL works within the LAN

Hibernate, Standby, and Power-off the WOL computer, while clicking Send on the second computer, to test each mode to make sure WOL is working.

Once this step is working, you can go on to making WOL work when you are outside your LAN, such as at a cafe or another remote location.

[edit]Troubleshooting

Wake On LAN is usually disabled by default in most PCs. This feature, if optional, must be enabled in your BIOS otherwise WOL isn't going to work. Consult your motherboard's manual and BIOS screen (DEL at startup, usually). If you don't see the WakeOn-type options in your BIOS, usually somewhere in Power Management, your motherboard may not support WOL.

• A good place to start is here: [1]

[edit]WOL Methods

[edit]WOL through Telnet/SSH

Note: This is the preferred method to send WOL magic packets remotely.

If you have local or remote Telnet/SSH access to your router, you can wake up a machine on the LAN by using the following command:

Note that the full path to '/usr/sbin/wol' is important. Simply 'wol' will not work.

Substitute AA:BB:CC:DD:EE:FF with the actual MAC address of the computer which you wish to boot remotely. Likewise, replace 192.168.1.255 with the actual broadcast address of the network (192.168.1.255 is the broadcast address when the machine has an IP of 192.168.1.x and subnet mask of 255.255.255.0). Replace 'PP' with the port number your machine listens on (usually 7 or 9).

[edit]Remote Wake On LAN via Port Forwarding

To remotely wake up a computer over the Internet using Wake On LAN- follow these instructions:

1 - Create a port forward rule on the Web Interface (Applications & Gaming -> Port Range Forward) to the chosen ip:

• Here, 9 is the default, but you can use any port number so long as your client wake-up application can talk to a port other than 9. Most WOL services will use either UDP port 7 or 9.
• 192.168.1.254 is just an IP address in your LAN's subnet; it can be any IP, as long as it is not assigned to any device on your network.

2 - Add a static ARP entry by typing the following line into the Administration -> Commands section of the Web Interface and then saving with Save Startup.

• Do not change the FF:FF:FF:FF:FF:FF MAC address; this is a special MAC address used when broadcasting. WOL magic packets are constructed using the MAC address of the target computer, but should be and almost always are sent via broadcast; the MAC address used here controls with how the packet is sent, not how it is formed.
• The 192.168.1.254 IP address should correspond with the IP address you used in the previous step. Again, this IP should be in your LAN's subnet, and you must not assign this IP address to any actual device on your network.
• Explanation/rationale for this setup: Normally, WOL magic packets are sent to a special broadcast IP--to the final .255 in a subnet or to 255.255.255.255. Since port-forwarding to these special dedicated broadcast IPs does not work, what we need to do is create our own broadcast IP by taking an unused IP and assigning it a broadcast MAC and then port-forward to that.
• As an optional alternative, instead of arp, you can use ip neigh (which does the exact same thing as arp). Support for ip neigh was removed from DD-WRT starting with build 17650, and arp is unavailable in DD-WRT builds older than 5672.

• NOTE: SOME BCM USERS HAVE REPORTED ISSUES WITH ARP. SEE THIS:

3 - Reboot the router, or execute the startup commands manually.

• To wake your computer from the internet using the DD-WRT device DynDNS name (or if you know it, the public IP of the router), try one of the following services;

1. Mestrona's online WOL. You need to forward port 9 udp in step one, to use this service.
2. Wake-On-LAN Online. It works both on ports 7 and 9 and allows WOL by a single URL of the form: http://mobile.wakeonlan.me/?ip=HOSTNAME&mac=MACADDRESS. It also allows for scheduled wakeup over the internet.
3. To use the WOL Magic Packet application from a second PC:
   1. Host Name: DynDNS name of your DD-WRT device.
   2. Subnet Mask: 255.255.255.255
   3. MAC Address: WOL computer MAC address, not the DD-WRT MAC.
   4. Click the green Send button.

[edit]Automatic Wake-On-LAN Daemon

The Automatic WOL daemon will send out a periodic wake on lan packet at the intervals you specify. This may be useful to keep a system online most of the time even if it is turned off. (eg: A Media Center PC).

For Interval you can enter a value in seconds as low as 15 seconds and as high as 86400 seconds (1 day).Host name should be the broadcast address for your LAN. eg: 255.255.255.255 or 192.168.1.255.SecureON Password is computers that have a BIOS feature that secures the WOL function. If you do not have a BIOS that requires this form of password then you can leave the box blank or type in 00-00-00-00-00-00.MAC Address(es) should contain the MAC address of the networked machines you want a WOL to be sent to on your LAN.

The packets generated by the WOL daemon are sent to UDP port 40000. You likely will not need to worry about this unless the system you are attempting to send the WOL packet is on another subnet or you are trying to monitor the packets.

Teamviewer Wake Up On Lan

note: the UI says that the Interval accepts a range of 1-86400 seconds but it will only send out a WOL packet at a minimum of 15 second intervals. All values below 15 are accepted but the interval will still be every 15 seconds.

A useful tool for watching the WOL packets on a Windows computer is available at www.depicus.com/wake-on-lan (use port 40000 when monitoring) Or you can use a more generic protocol analyzer tool like Wireshark.

Teamviewer Wake Up On Lan Macbook

[edit]WOL Scripts

1. Wake up a specific host when triggered from the internet: Web Server Wake-up.
2. To wake by name: Name-based WOL.

[edit]See Also (forum discussions)

[edit]References

Teamviewer Manual Wake On Lan